Home
CLASSIFICATION GA-1Streets, Roads & Highways
Road & Highway Construction
New road constructionSubdivision road constructionAsphalt pavingConcrete pavingHighway site prepCulvert installation
Parking & Site Paving
Parking lot pavingPublic parking areasDriveway pavingSidewalk constructionNew seal coatingPavement striping
Earthwork & Site Preparation
Grading & earthworkSite clearing & prepStormwater drainage
View Specialty Page
CLASSIFICATION GA-2Roadway Maintenance & Repair
Pavement Repair
Pothole patchingCrack sealingAsphalt patching & repairConcrete repairRoad maintenance
Pavement Preservation
Seal coat maintenanceAsphalt overlayRoad rehabPavement preventive maintenance
Municipal & DOT Contracts
Street maintenance programsDOT repair workPublic works repairFacility parking maintenance
View Specialty Page
CLASSIFICATION GS-21Roofing
Roof Systems
TPO roofingEPDM roofingPVC roofingFlat & low-slope roofingSteep slope roofingCommercial roofingResidential roofing
Roof Replacement & Reroofing
Full roof replacementReroofing (recover system)
Roof Coatings & Restoration
Elastomeric coatingsSilicone coatingsRoof restorationRoof coating systems
Waterproofing & Flashing
Roof waterproofingFlashing installationSheet metal (roofing incidental)
Roof Repair & Maintenance
Leak repairEmergency repairFacility roofing repairRoof preventive maintenanceRoof inspection
View Specialty Page
AboutPortfolioContact
Roof Flashing Installation
GS-21 Certified Roofing

Roof Flashing Installation

Professional roof flashing for parapet walls, penetrations, HVAC curbs, and edge metal — the critical details where 90% of commercial roof leaks originate.

(505) 502-4914
GS-21 LicensedAll Flashing TypesHeat-Welded to MembraneProbe-Tested
Service Overview

Flashings Are Where Roofs Fail

Over 90% of commercial roof leaks originate at flashings — not in the field membrane. Parapet wall base flashings, pipe penetration flashings, HVAC curb flashings, drain flashings, and edge metal terminations are all transition points where the membrane system must make a watertight transition to another surface. Improperly installed or deteriorated flashings allow water infiltration that damages interior spaces and structural components. We treat flashing installation as the most critical phase of any roofing project.

  • Membrane pipe boot flashings for all roof penetrations — heat-welded to field membrane
  • HVAC equipment curb flashings with proper membrane-to-curb transition details
  • Parapet wall base flashings extending minimum 8 inches above finished roofing
  • Edge metal fascia systems at all roof perimeters with proper membrane termination bar

90% at Flashings

Leak Origin

Heat-Welded

TPO/PVC Flashings

100% Probe-Tested

Testing

Membrane Flashings vs. Sheet Metal

Modern TPO and PVC roofing systems use membrane-to-membrane flashings — factory-fabricated or field-fabricated membrane pieces heat-welded to the field membrane at all penetrations and transitions. This creates a completely homogeneous, seamless watertight system. Sheet metal counter-flashings are used at wall terminations where the membrane cannot be mechanically fastened — always with lap sealant and proper anchoring to prevent wind uplift.

Est. 2016
EL

Patriot Asphalt and Construction

Albuquerque, NM · Licensed, Bonded & Insured · Bonded & Insured

Free Consultation

Get Your Flashing Estimate

Free inspection and flashing repair or installation proposal throughout Greater Albuquerque Area.

Get In Touch

Service Area

Albuquerque · Albuquerque · Greater Albuquerque Area

Response Time

Free inspections Mon–Sat

★ Licensed, Bonded & Insured · Bonded & Insured · Est. 2016